Welcome to Nantong Fleck Fluid Equipment CO., LTD.!
Introduction of equipment characteristics of wet pulverizer
wet pulverizerIt is suitable for grinding, emulsifying, homogenizing, crushing, dispersing, stirring and mixing data processing of different crushing solid-liquid mixing materials. When in use, it can realize efficient and rapid continuous discharging without adding grinding coal. At the same time, it also has the advantages of small floor space, short production development cycle, low energy consumption cost and so on. What are the precautions for wet grinder? Let's take a brief look at it.
1. The processed materials must be selected and the sheep feed crusher must be used to remove hard debris such as metal and stones so as not to damage the machine. The humidity of the processed materials should also meet the requirements. Generally, when crushing dry materials, the water content of the feed crusher should not exceed 12% ~ 14%; when mixing and crushing, appropriate water should be prepared.
2. Turn the pulley by hand to see if there is any collision or friction, and then idle for 2~4rain to check the steering of the crusher. The standby group can work only after running smoothly.
3. When working, the sleeves of the operator should be tied tightly, standing on the side of the machine, and it is strictly forbidden to feed people with hands close to them.
4. When the wet pulverizer is in operation, the operator shall not leave the unit or disassemble the interior of the pulverization chamber during operation. Tools cannot be placed on stockpiles and machines. If you hear any abnormal sound from the machine, stop it immediately, and then disassemble it for inspection and troubleshooting.
5. After each parking inspection, the storage in the crushing room should be cleaned up. It is not allowed to start with load. It can only be refilled after the machine is idling smoothly.
6. When the bearing temperature is too high, stop the machine for inspection, find out the cause and eliminate the fault.
7. When beating with a grinder, constantly add water to it, be careful not to splash water on electrical components, and do not touch electrical components with wet hands to avoid electric shock accidents.
8. before the completion of each work, should be idle 2~3 minutes, standby material completely discharged, can stop the crusher and fan.
9. Check the fastening and lubrication of various parts before operation, check whether the vulnerable parts such as blades need to be replaced, and check the operation flexibility of the machine.
10. In production, the machine generally runs for 1 to 2 minutes after starting. When the grinder reaches the rated speed, it can run normally without abnormal sound, and then it can be operated in feed. If an abnormality is found, the inspection should be stopped and the cover should not be opened. Check and adjust to ensure safe operation.
11. Before the shutdown, the feeding should be stopped 2 to 3 minutes in advance to discharge the materials in the crushing chamber.
wet pulverizerIn the fields of pharmaceutical, new building materials, chemical industry, agriculture, electronics, waste resource regeneration and food production and processing, the information of crushed solid-liquid mixed materials is studied and processed by crushing technology. What are the advantages of wet pulverizer? Let's take a brief look at it.
1, shorten the route, reduce the batching process. 2, reduce energy consumption, easy to fine production. Noise pollution and dust pollution are greatly reduced. 4, special protection of heat sensitive materials for greater applicability. 5. Suitable for crushing fiber materials and soft materials.
wet pulverizerWhat are the characteristics of the equipment? Let's all have a brief understanding.
1. For example, the smaller the particles, the closer they are, the higher the uniformity, and the better the effect. 2. It is convenient to separate the components in the raw material particles, such as wheat crushing and starch preparation. 3. Improve the fluidity of the material and realize the fluidization operation; for example, fluidized bed drying. 4, improve the process performance of the material. For example, after crushing, the surface area increases, and the drying and dissolving properties of the material are improved.
Recommended Information
Crushing pump - pigment crushing test
2023-11-30
Precautions for operating an emulsifier
2023-11-14
Delivery of hygienic rice grinder
2023-11-07
Polyacrylamide mixed homogenization test
2023-10-23
Contact Information
No. 5, Youth East Road, Science and Technology Pioneer Park, Qidong City, Jiangsu Province
Focus on us
Mobile Website
Copyright©2023 Nantong Fleck Fluid Equipment CO., LTD.
Powered by 300.cn | SEO | Business License