Engineering plastic shredder_Nantong Fleck Fluid Equipment CO., LTD.

At present, the pulverization of engineering plastics on the market is a blank area. The crushing of engineering plastics in the factory can only rely on the old-fashioned pulverizing equipment, which produces large heat, small output, high pollution, high noise, and can not reach the current new engineering. The fineness requirements of the finished plastic products, in this case, China's current engineering plastics new technology, is no engineering plastics special crushing equipment and can not improve the grade and output of the products, for which Nantong Fleck specially designed and developed a A new type of pulverizer for engineering plastics.

Corresponding parameter set not found, please add it in property template of background

model	Processing capacity m³/h	Motor Power kw	Import and export size mm	Mesh size mm
FSJ-G50	0.1-0.5	7.5-15	50/40	1、3、5
FSJ-G60	0.5-1	11-22	65/50	1、3、5
FSJ-G80	0.8-3	18-30	80/65	1、3、5
FSJ-G100	1-5	22-37	100/65	1、3、5
FSJ-G125	3-8	30-55	125/100	1、3、5

Main structure of engineering plastic crusher

The main structure of the engineering plastic pulverizer is composed of a motor, a coupling body and a pump casing. The equipment is divided into two types: horizontal and split; the horizontal equipment is imported at the horizontal level of the casing, the outlet is below the casing, the split device is imported above the casing, and the outlet is below the casing. The casing is divided into: cutting Area, coarse crushing area, fine crushing area, filtration area and circulating crushing area, engineering plastic particles do not heat under the cooling of water, and completely discharge according to the requirements. The main features of engineering plastic crusher: no heat, high output, fine Good degree and fineness of discharge can be controlled.

The main principle of engineering plastic crusher

The main principle of engineering plastic pulverizer is to feed the raw materials of engineering plastic into the working cavity of engineering plastic pulverizer through other special equipment, and set the rough cutting area of the imported plastic. Three pieces of Fengli blade are set on the rough cutting area to make the nozzle High-speed shear pulverization of engineering plastics for cutting baffles, and then the coarsely crushed engineering plastic granules enter the pulverized cutting zone with Dora hammer knives for hammering and cutting, then enter the fine crushing area, and then have the next set of hammer knives. Hammering and cutting fine crushing, after the engineering plastic reaches a certain design particle fineness requirement, it is sprayed out from the stator aperture together with water into the outlet filtration zone, and a filter device is arranged in the outlet filter material zone, and the material number is designed according to user requirements. Filtration is carried out, and the qualified particles are discharged, and the unqualified particles are sucked into the circulating crushing chamber on the inside of the filtering device to be re-cut, pulverized, and refined. Moreover, the circulating pulverizing device continuously performs a plurality of cycles of pulverization so that the discharged granules reach the standard design mesh.

Accessories: Equipment selection parameters and technical requirements (downloadable)

　First, the technical parameters of your company's materials:

Material medium

Processing capacity(m³/h)

Liquid category

□Water-based,　□Oily,　□Solvent

Solid category

□Agglomerate,　□Crystals,　□Primary particle

Liquid to solid ratio(%)

Viscosity Pa.s

Material flow

□Very good (water),　□可以，　□difference,　□Very poor

Feed contains

Large particles mm,Take up %

Medium particle mm,Take up %

Small particles mm,Take up %

Solid particles

(□fragile, □Not fragile, □Viscous)

Discharge granule μm

Head m

temperature ℃

Remarks:

　Second, your company's requirements for equipment:

　1. Material contact part material

□stainless steel 304，　□stainless steel 316L，　□Duplex steel 2205，　□TA2，　□HastelloyC276

　2, rotating stator material

□stainless steel 304，　□stainless steel 316L，　□Duplex steel 2205，　□TA2，　□Hastelloy C276，

□Wear-resistant steel NM500，　□Wear-resistant steel 38CrMoAl，　□Tungsten carbide treatment,　□Emery treatment

　3, sealed

□Ordinary single-sided mechanical seal,　□Ordinary double-sided mechanical seal,　□Custom double-sided mechanical seal

O-ring configuration

□Ding O-ring,　□Fluoro rubber O-ring,　□Fluorine-containing O-ring,　□Perfluoroether O-ring

Material contact surface

□Tungsten carbide-silicon carbide,　□Tungsten carbide-tungsten carbide,　□Silicon carbide-silicon carbide

　4, the motor

□Ordinary motor,　□Inverter motor,　□Ordinary explosion-proof motor,　□Explosion-proof inverter motor,　□Dust explosion-proof motor

□Class 2 energy efficient motor,　□Marine motor,　□Waterproof motor

□Self-contained control box

□With control box

　Third, the corresponding device model:

Full name of the equipment

Model

Processing capacitym³/h)

Motor Power(kw)

Amount

Remarks

other

Fill in the unit:　　　　　　　　　　Fill in the person:　　　　　　　　　　phone:

Daily chemical industry: AES、LAS、AOS、MES、K12、Glycerin, sorbitol, fatty alcohol, shower gel, skin cream, shampoo, hand soap, toothpaste, soap, detergent powder, etc.

Fine Chemicals:Dyes, pigments, various pastes, chemical additives, adhesives, 107 glue, silicone oil, leather oil, emulsion explosives, various colloidal materials.

Food:Chocolate, condensed milk, yogurt, honey, syrup, sucrose, tomato juice, concentrated juice, jam, ice cream, milk, yeast mud, meat, jelly, condiments, vinasse, soy protein, flour, etc.

Paper production:Polyacrylamide (PAM), calcium carbonate, starch paste, carboxylated butylbenzene/propylbenzene latex, rosin, rosin gum, pulp, filler, dry strength: agent, wet strength agent, sizing agent, retention and drainage aid, elimination Foaming, coating, water treatment chemicals, etc.

Chemical fiber:Viscose porridge, PVA, vinylon pulp, acrylic pulp, amine pulp, polyester chips, polyester, polypropylene, rayon, functional fiber, etc.

Medical medicine:Various ointments, extracts, drug lotions, pill pastes, syrups, health products, pharmaceuticals, etc.

Coating:Paints, coatings, inks, insulating varnishes, resins, auxiliaries, organic solvents, etc.

暂未实现,敬请期待

86-513-83351692

Engineering plastic shredder

Products